I frequently transfer data over the LAN at a higher rate than my internet connection.
Kinda wish it was easier to test the connection speed between devices tbh, unless someone knows a good way of doing it but many devices are so locked down I am not sure how you would.
Even when doing that, the bottleneck is the storage write speed. you can have 1Tb internet connection and it wouldn’t matter unless you have enough users in a home.
NVMEs are claiming sequential write speeds of several GBps (capital B as in byte). The article talks about 10Gbps (lowercase b as in bits), so 1.25GBps. Even with raw storage writes the NVME might not be the bottleneck in this scenario.
And then there’s the fact that disk writes are buffered in RAM. These motherboards are not available yet so we’re talking about future PC builds. It is safe to say that many of them will be used in systems with 32GB RAM. If you’re idling/doing light activity while waiting for a download to finish you’ll have most of your RAM free and you would be able to get 25-30GB before storage speed becomes a factor.
That is true, given everyone uses good quality nvmes, which is not always the case, but honestly, 1Gbps fiber is enough for a home with multiple users. Even if, assuming the storage is not the bottleneck, unless you need often very large lan transfers, should be more enough with 1Gbps.
Anyway, I guess i’m sidestepping the initial topic. bottom line: cool cheap tech for companies, not so much for home users.
Low latency means low compression. Low compression means high bandwidth.
1080p60 NDI will be 200mbps. If you are doing 2160p60, that’s 800mbps (which is about the limit I would run 1gbe at). Doesn’t leave much overhead for anything else, and a burst of other traffic might cause packet drops or packet rejection due to exceeding the TTL.
2.5gbps would be enough.
But I see 2.5gbps and 5gbps as “stop-gaps”. Data centers standardised on 10/40gbps for a while (before 25/100 and 100/400) - it’s still really common tbh - so the 10gbps tech is cheap.
I don’t see the point in investing in 2.5/5gbps
You need more than10Gb/s at home? I mean we all know the 640Kb meme but I’m curious here :-)
I frequently transfer data over the LAN at a higher rate than my internet connection.
Kinda wish it was easier to test the connection speed between devices tbh, unless someone knows a good way of doing it but many devices are so locked down I am not sure how you would.
Even when doing that, the bottleneck is the storage write speed. you can have 1Tb internet connection and it wouldn’t matter unless you have enough users in a home.
NVMEs are claiming sequential write speeds of several GBps (capital B as in byte). The article talks about 10Gbps (lowercase b as in bits), so 1.25GBps. Even with raw storage writes the NVME might not be the bottleneck in this scenario.
And then there’s the fact that disk writes are buffered in RAM. These motherboards are not available yet so we’re talking about future PC builds. It is safe to say that many of them will be used in systems with 32GB RAM. If you’re idling/doing light activity while waiting for a download to finish you’ll have most of your RAM free and you would be able to get 25-30GB before storage speed becomes a factor.
That is true, given everyone uses good quality nvmes, which is not always the case, but honestly, 1Gbps fiber is enough for a home with multiple users. Even if, assuming the storage is not the bottleneck, unless you need often very large lan transfers, should be more enough with 1Gbps.
Anyway, I guess i’m sidestepping the initial topic. bottom line: cool cheap tech for companies, not so much for home users.
edit: wording
We don’t all have 1Gbps fiber though, but even without it I can still benefit from 1Gbps ethernei
Not all data transfer is sending stuff to storage, streaming your display live at a high bitrate for example never needs to go into storage.
Is more than 1Gbps needed for that? That seems insane, but I’m old and watch stuff in full HD so what do I know.
Low latency means low compression. Low compression means high bandwidth.
1080p60 NDI will be 200mbps. If you are doing 2160p60, that’s 800mbps (which is about the limit I would run 1gbe at). Doesn’t leave much overhead for anything else, and a burst of other traffic might cause packet drops or packet rejection due to exceeding the TTL.
2.5gbps would be enough.
But I see 2.5gbps and 5gbps as “stop-gaps”. Data centers standardised on 10/40gbps for a while (before 25/100 and 100/400) - it’s still really common tbh - so the 10gbps tech is cheap.
I don’t see the point in investing in 2.5/5gbps